CDLPre-Trip InspectionClass ASkills Test

2025 Class A Pre-Trip Inspection: The Outside Walk-Around, Step by Step

Walk the Class A pre-trip from headlights to rear doors, with the exact wording examiners expect for the engine, steer axle, coupling and trailer.

October 8, 2026 · Commercial Driver Prep team
2025 Class A Pre-Trip Inspection: The Outside Walk-Around, Step by Step

The pre-trip inspection is where most Class A candidates lose points on test day. Backing and the road drive get more attention, but the inspection comes first. It’s also the one part of the skills test you can fully script ahead of time. Once you know the order and the wording, it’s mostly a memory exercise.

This guide covers the outside walk-around of the modernized Class A test. It assumes you’ve already finished the in-cab inspection and air brake check. If you haven’t learned those yet, start with our in-cab and air brake check walkthrough.

How the outside inspection fits into the skills test

The CDL skills test has three parts, and you must pass each one before you move on:

PartWhat you doWhat sinks most candidates
1. Vehicle inspectionIn-cab check, air brake test, outside walk-aroundSkipping items or using vague wording
2. Basic vehicle controlUp to four backing/parking maneuversToo many pull-ups and encroachments
3. Road testDriving on public roads with the examinerShifting, lane control, intersections

Everything you say during the inspection comes from the vehicle inspection section of your state’s CDL Manual. That section is built on the FMCSA model manual. Examiners grade against a fixed checklist, so naming the right part and the right defect matters more than sounding confident. For a look at how the modernized test is scored, see what changed in the modernized pre-trip.

Tip: For each item, say what it is, how it’s mounted, and what defects you’re looking for. For example: “Mirror is securely mounted, not cracked or broken, clean and properly adjusted.”

Step 1: The external light check (before you step out)

Do this from the cab, before you start walking. Many candidates forget it.

  1. Tell the examiner: “I’d like to do an external light check. Could you assist me?”
  2. Once they’re standing outside, switch on and name each light: headlights (low and high beam), left turn signal, right turn signal, four-way flashers, clearance and marker lights.
  3. Ask them to confirm the lights on the front, sides and rear.

Then, at each light during the walk-around, say: “Lenses and covers are the proper color, not broken or missing, and working properly.” Lights on the front and sides should be amber and white, and lights on the rear should be red.

Step 2: Front of the truck and under the hood

Start at the front and look at the ground before you open anything:

  • No puddles on the ground and no fluid dripping from the underside of the engine or transmission
  • The vehicle is sitting level, which tells you the suspension has no obvious problems

To open a heavy tilt hood, release the latches on both sides. Then use three points of contact: one foot on the bumper or grille step, both hands on top of the hood. Lean back and let your body weight pull it open.

The three fluid levels (engine off)

FluidHow you check itWhat you say
Engine oilDipstick (often yellow, usually driver’s side)“Pull, wipe, recheck. Level is between the min and max marks.”
Power steering fluidDipstick or reservoir”Pull, wipe, recheck. Level is within the safe operating range.”
CoolantSight glass on the reservoir”Level is visible in the sight glass at the proper operating level.”

You can check the fluids in any order. Just make sure you name all three.

Remember: Never open the coolant or radiator cap on a hot engine. Hot coolant under pressure can cause serious burns. Say this out loud to the examiner, because it shows you know the safety rule.

Hoses and leaks

Look at the hoses on both sides of the engine and say they are “not leaking, cracked, torn, or missing.” Then listen for air leaks.

Step 3: The steer axle, from tire to brake

The modernized Class A test usually asks for full detail on the steer axle only. Learn this sequence well, but in real life inspect every tire on every axle before every trip.

Tires

  • Inflation: Check with a tire gauge at the valve stem. Pressure should match the manufacturer’s spec on the sidewall or door placard.
  • Tread depth: At least 4/32” on steer tires and 2/32” on all other tires (49 CFR 393.75).
  • Condition: Tread is evenly worn, with no cuts or damage to the tread or sidewall, no bulges, and the tire is properly seated on the rim.
  • Valve cap and stem: Not missing, damaged or leaking.

Rims, lug nuts and studs

  • Rim: No welding repairs, not cracked or bent, no rust trails
  • Studs and bolt holes: Not cracked, damaged, out of round or elongated
  • Lug nuts: All present and none loose. Signs of looseness include rust trails and shiny threads.

Did you know? Rust trails usually mean water has been getting in behind a loose nut. Shiny threads mean the nut has been moving and rubbing. Either one means the wheel needs attention before you drive.

Behind the tire: suspension and brakes

  • Spring mounts and leaf springs: Not cracked, broken, shifted or missing parts
  • Shock absorber: Securely mounted, not damaged or leaking
  • Air bags (air-ride suspension): Secure, not damaged, not leaking
  • Brakes: Brake chamber, hoses and slack adjuster are secure and not leaking. The brake drum and lining have no contaminants such as grease or oil that could reduce braking.

When you finish the axle, close the hood and move down the driver’s side.

Step 4: Down the driver’s side

ItemWhat you say
MirrorsSecurely mounted, no missing bolts, clean and not cracked
Battery boxBatteries secure, connections tight, cables not cracked or worn, no excess corrosion. You can describe the batteries without opening the box.
Fuel and DEF tanksCaps tight, no leaks from the tanks or lines, tanks securely mounted
Frame and cross-membersNot cracked, bent or broken, no holes or illegal welds. This applies to both the tractor and the trailer.

Step 5: The coupling system

This section is what makes the test a Class A test. Take it slowly. If you need a refresher on why coupling matters, our post on combination vehicles, coupling and air lines explains it.

Air and electric lines

  • Glad hands: Properly seated, seals in good condition, no air leaks (listen for them)
  • Air lines and electric line: Not cut, spliced, taped or worn. They are not tangled with each other and not dragging against tractor parts.

Fifth wheel and kingpin

  1. Skid plate: Securely mounted to the platform, not cracked or broken, properly lubricated
  2. Kingpin: Not bent, cracked or damaged
  3. Apron: The underside of the trailer that rests on the fifth wheel is not bent, cracked or damaged
  4. No gap between the apron and the skid plate
  5. Locking jaws: Fully closed around the shank of the kingpin, not the head
  6. Release arm: In the locked position, with the safety latch engaged
  7. Slider and locking pins (if the fifth wheel slides): Pins fully engaged so the fifth wheel can’t move forward or back

Tip: You usually don’t have to crawl under the trailer on test day. From the driver’s side, ask “Would you like me to go underneath?” Most examiners say no, but you still need to name every item above.

Step 6: Landing gear

  • Fully raised, with no missing parts or bent supports
  • Crank handle secured in its holder
  • Landing pads not damaged
  • Enough clearance between the landing gear and the tractor. If the tractor sits too close, its frame or mud flaps can hit the landing gear in a tight turn.

Step 7: The rear of the trailer

This is the easiest part of the walk-around:

  • Lights: Taillights, brake lights, turn signals and clearance lights are the proper color and not broken or missing
  • Reflectors and reflective tape: Proper color, clean and securely attached
  • Doors: Securely closed and latched, and the hinges are not damaged

For the complete inspection, including the in-cab check and the rest of the trailer, use our complete 2026 Class A walk-around.

Common pre-trip mistakes

MistakeFix
Skipping the external light checkDo it before you leave the cab, every time you practice
Saying “looks good”Name the defects: “not cracked, broken, leaking or missing”
Mixing up the tread depthsSteer tires 4/32”, all other tires 2/32”
Saying the jaws are “closed”Say the jaws are “closed around the shank of the kingpin”
Forgetting the hoses on the passenger sideCheck both sides of the engine compartment

Turn the walk-around into test-ready knowledge

The skills test checks whether you can say the inspection. The written General Knowledge test checks whether you understand it. Both come from the same CDL Manual sections. Questions about tread depth, coupling, leaks and safe hood handling come up on both.

Our CDL Test app gives you complete practice for the CDL General Knowledge test and every endorsement. Each answer’s explanation ties back to the CDL Manual. You can also try the Pre-trip Inspection quiz here on the site to test yourself on the items in this guide. The CDL Test app is one of three focused apps in the Commercial Driver Prep suite, which together cover 1200+ questions across CDL, HazMat and Air Brakes.

Start with a free quiz right now: pick a topic →

Frequently asked questions

What is checked on the outside of a Class A pre-trip inspection?
The outside walk-around covers lights and reflectors, leaks under the vehicle, the engine compartment (oil, power steering fluid, coolant, hoses), the steer axle (tires, rims, lug nuts, suspension and brakes), the driver's side (mirrors, battery, fuel and DEF tanks, frame), the coupling system (air and electric lines, fifth wheel, kingpin, apron, locking jaws, release arm, slider pins), the landing gear, and the rear of the trailer (lights, reflective tape and doors).
What is the minimum tread depth for CDL truck tires?
Under FMCSA rule 49 CFR 393.75, steer tires need at least 4/32 of an inch of tread in every major groove. All other tires need at least 2/32 of an inch. These two numbers come up both on the skills test and on the General Knowledge written test.
Do I have to crawl under the trailer to inspect the fifth wheel on the CDL test?
Usually not. Most examiners let you point to the coupling parts and describe them from the driver's side. You can ask, 'Would you like me to go underneath?' Most will say no, but you still have to name every part and say what you're checking it for.
Do I have to inspect every tire on the CDL pre-trip test?
On most modernized Class A tests you only describe the steer axle in full detail. Other axles may be checked in less detail or not at all, depending on your state. In real life, inspect every tire on every axle before every trip. A problem you catch early costs less to fix and keeps you safer.
What is an external light check on the pre-trip inspection?
Before you get out of the cab, you ask the examiner to help with a light check. While they stand outside, you switch on each light and say what it is: headlights, high beams, left and right turn signals, and four-way flashers. Then they confirm the lights work on the front, sides and rear. Candidates often skip this step and lose easy points.

Put what you've read into practice

Free practice quizzes for CDL, HazMat and Air Brakes — no signup.